Personal tools
You are here: Home Distribution SLF 5 installation Scientific Linux Fermi 5 Installation
Views
Document Actions

Scientific Linux Fermi 5 Installation

by Troy Dawson last modified 2008-12-09 11:37
History
Action Performed by Date and Time Comment
Publish Troy Dawson 2008-12-09 12:37 No comments.

Installation guide for Scientific Linux Fermi 5

This web page describes installing for any Scientific Linux Fermi 5.x distribution. Simply replace anyplace that says 5.x or 5x with the appropriate version number. So if you were installing Scientific Linux Fermi 52, then you would replace 5.x with 5.2, and 5x with 52 wherever you see it in this document.

SL 5.x Pre-Installation Checklist

Installation Media

Network Setup

This is a must if you are doing a network install. It is optional if you are doing a CD or DVD install.

  • DHCP
    This is where a IP address and hostname get assigned to your machine for a limited time. Most laptops work this way, where you just plug in your computer and you automatically are on the network. If you will be using DHCP during the install, you do not need to figure out your IP address, it will be detected and used automatically.
    NOTE: If your computer's network card is not registered with Networking, and you attempt to do a DHCP network install at Fermilab, you will not be able to reach the distribution servers. You will get an error saying that it could not find the distribution and ask you where the distribution is.
    You MUST have your machine registered with networking to do a DHCP network install onsite.
  • Static IP Address
    Using a static IP address is the prefered way to network desktop and server machines. You will need to get a IP address from the DataComm Group. This generally takes a day to get into the system.
    The MAC (hardware) address of the ethernet card is needed in order to get a IP address.
    • We are currently determining the easiest way to obtain the MAC address. When we do we will have those instructions here.
    DataComm will supply you with your IP address, along with other information. During the install you will need
    • The IP address (suppliedby DataComm).
    • The network Netmask (suppliedby DataComm with the IP address).
    • The network Default Gateway IP address (supplied by DataComm with the IP address).

Scientific Linux Fermi v5.x Installation Steps

Installation Instructions

  • Network Install: Note that the very first part of the install is done in text mode. This is because we simply cannot fit the graphical installation onto the initial boot image. Once you connect to the installation server it will try to startup the graphical install. Until that point, here are a few things to note.
    Use the Tab/Alt-Tab keys to navigate between elements.
    The <space> key selects/deselects items.
  • CDROM Install: The first cdrom is bootable if your BIOS is configured to boot from cd-roms.
  • Text Install: For either network or cd-rom install, type in 'linux text' and then return at the very first step.

Click on Image for full size image.
Click on Section Name for detailed instructions.
Sections marked with a ** have default screens inside their section.

Bootup Screen (Enter) or [http text](Enter)

Language Selection(Shouldn't see normally)(Network install only) [OK]

Keyboard(Shouldn't see normally)(Network install only) [OK]

Installation Method(Shouldn't see normally)(Network install only) Pick installation method then [OK]

Configure TCP/IP(Network install only)

Either:
  • Choose DHCP
  • or
  • Enter the IP address (from your Network Manager)
    Netmask (from your Network Manager)
    Default gateway (from your Network Manager)
    Primary nameserver (from your Network Manager)
[OK]

HTTP, NFS, or FTP Setup(Shouldn't see normally) (Network install only)
You should point your machine to your network installation server.
Depending on your network installation server, the path may be different. You should check to make sure you put the correct path in.
We are using i386 as an example, depending on what you are installing, you can replace that with x86_64. But you must have gotten your installation media from the appropriate images area, because an i386 network install cd will not work with x86_64 install directory, or vice versa.

HTTP server name: linux01.fnal.gov
Scientific Linux 5x (Fermi) directory: /linux/slf5x/i386

NFS server name: linux.fnal.gov
Scientific Linux 5x (Fermi) directory: /export/linux/slf5x/i386

NOTE: FTP Installs are *not* recommended for SLF5
FTP server name: linux.fnal.gov
Scientific Linux 5x (Fermi) directory: /linux/slf5x/i386
[OK]

At this point, the installation try's to startup the graphical installation, unless you are doing a text installation. If for some reason the installation is unable to startup the graphical mode, then it will run the installation in text mode. Although this is a rare occurance, it does happen from time to time.
At this point, you can also take out the network install cd if you wish, it is not used again.

Welcome [Next]

Upgrade Examine (Only if upgradable) Choose between upgrading or a fresh install [Next]

Installation Type Pick installation type then [Next]

Disk Partitioning Setup Disk Druid [Next]

Partitioning Partition Correctly then [Next]

Boot Loader Configuration [Next]

Network Configuration Edit if necessary then [Next]

Time Zone Selection [Next]

Set Root Password type in Root's password twice then [Next]

Package Group Selection Select/Remove desired packages then [Next]

The installation will proceed.
This is the usual time to get a snack or stretch.

Congratuations Remove the cdrom or USB drive [Exit]